Minus Pad extreme 2 Thermal Pad

Minus Pad extreme 2

The Minus Pad extreme 2 thermal pad features outstanding thermal conductivity and low thermal interface resistance, making it ideal for high-performance applications.

$37.33

Content: 4800 mm² ($0.78 / 100 mm²)

Prices incl. VAT plus shipping costs

Size

100 x 100 mm

120 x 20 mm

Thickness

0.5 mm

1,0 mm

1.5 mm

2,0 mm

3,0 mm

Content

1 pc.

2 pcs.

EAN: 4260711992179

MPN: TG-MP-E2-120-20-05-2

Product information " Minus Pad extreme 2"

The Thermal Grizzly Minus Pad extreme 2 thermal pad is designed for high-performance applications. Due to the varying particle sizes of its individual components (aluminum oxide, aluminum hydroxide, aluminum powder), even the smallest gaps in the carrier material (matrix) can be filled with thermally conductive particles. This is especially true for the surfaces (top and bottom) of the Minus Pad extreme 2, where the optimized material composition offers low thermal interface resistance and promotes optimal heat transfer.

Properties

Outstanding thermal conductivity
For high-performance applications
No curing
Electrically non-conductive

High-performance thermal pad for extreme applications

A soft consistency allows the Minus Pad extreme 2 to conform well to the surfaces of the heat source and cooler. Minus Pad extreme 2 is electrically non-conductive and does not cure or harden over time, even with extended use.

Available in dimensions of 120 x 20 mm and 100 x 100 mm, as well as in thicknesses of 0.5 mm, 1 mm, 1.5 mm, 2 mm, and 3 mm.

Outstanding thermal conductivity

For high-performance applications

No curing

Electrically non-conductive

Minus Pad extreme 2

What thickness of Minus Pad extreme 2 do I need, and how do I account for compression and mounting pressure?

Choose the thickness of Minus Pad extreme 2 according to the specific cooler's requirements or the actual gap and compression behavior. There is no universal pad thickness for a GPU, VRAM or SSD model. A pad that is too thin makes no contact, while one that is too thick can lift the cooler off the main chip. Compression depends on the original thickness, area and mounting pressure. Check the contact imprint and follow the mounting instructions. An incorrect thickness cannot be compensated for by tightening further. External databases such as paddb.com can provide guidance on the pad thickness needed for your graphics card. You can measure used pads with a caliper such as TG Caliper. The area measured may already be compressed. The measurement is therefore only a guide, and the required original thickness may be greater.

What cooling performance does Minus Pad extreme 2 offer, and what matters when comparing the thermal pad ranges?

Minus Pad extreme 2 bridges gaps between components and the cooler. Cooling performance depends on pad thickness, compression and full contact. The Minus Pad series differ in heat transfer and deformability. Therefore, check thickness and contact again when switching series. Together with Minus Pad extreme, Minus Pad extreme 2 is among the highest-performing Thermal Grizzly pads. Compared with its predecessor, it offers a softer consistency and lower thermal contact resistance while maintaining similarly high thermal conductivity. Basic is the affordable entry-level option, while Advance offers higher performance than Basic. Minus Pad 8 ranks above Advance in performance, while Pro offers very good performance.

Which components and contact points is Minus Pad extreme 2 suitable for?

Minus Pad extreme 2 is intended as a gap filler between components such as VRAM, voltage regulators or SSD components and their cooler. Choose thickness and dimensions according to the cooler's requirements and the actual gap. For the thin interface on a CPU heatspreader or CPU/GPU die, use the thermal interface material intended for that purpose. A Minus Pad is not a replacement there for paste, a liquid metal interface or a suitable sheet.

What is included with Minus Pad extreme 2, and how can I obtain missing parts?

The package contents of Minus Pad extreme 2 depend on the selected size, thickness and pack quantity. Therefore, check the quantity listed for the specific item number. The films on the pads protect them during transport and application. First remove the film on the contact side, then remove the second film after positioning the pad and before installing the cooler. If the stated quantity is missing, send us proof of purchase and photos of the packaging and contents.

Where can I use Minus Pad extreme 2 in a laptop, and what should I consider during installation?

Minus Pad extreme 2 can be used in laptops for VRAM, VRMs or other contact areas designed to have a gap. The correct thickness and sufficient mounting pressure are essential. Particularly in laptops, pads that are too thick or too firm can lift the cooler. On CPU and GPU dies, use the thermal interface material intended for that purpose.

Can I combine Minus Pad extreme 2 with thermal paste, liquid metal or other thermal interface materials?

Install Minus Pad extreme 2 on clean contact surfaces without additional thermal paste or liquid metal. At the same time, the main CPU/GPU chip can use the other thermal interface material intended for it. In that case, the materials are used at different contact points. Pads can be stacked, but cooling performance may decrease slightly. Make sure the total pad thickness matches the available gap.

Can I continue using Minus Pad extreme 2 if it is torn, creased or damaged?

Small tears are generally not a problem as long as they do not leave a gap after installation and the contact area remains fully covered. Avoid creases and overlaps, as they can change the mounting height.

How do I cut Minus Pad extreme 2 to fit and remove the protective films?

Cut Minus Pad extreme 2 to size with sharp scissors or a blade on a clean surface. If possible, leave the protective films on the material when cutting it. First remove one film and position the pad on the contact surface. Only then peel off the second film, so the pad deforms less while being positioned. Both films must be removed before fitting the cooler. The intended component area should be fully covered without obstructing adjacent mechanical contact points.

Why are temperatures with Minus Pad extreme 2 too high or higher than expected?

Check the position and thickness of Minus Pad extreme 2 and the imprint on both contact sides. Remove all protective films and check whether an overly thick pad is lifting the cooler off the CPU/GPU die. Airflow or the liquid cooling loop must also be working properly. Do not increase mounting pressure beyond the permissible installation specification. A pad that is too thin may fail to contact the cooler, preventing heat from being transferred through the pad as intended.

How long does Minus Pad extreme 2 last in use, and when should I replace it?

A fixed replacement interval for Minus Pad extreme 2 is not generally necessary. During maintenance or if temperatures rise, check that the pad is still clean and makes full contact at all intended points. Small tears alone do not require replacement as long as they do not create a gap. Replace pads that are contaminated or no longer make even contact due to damage or permanent deformation.

Where can I find instructions, datasheets and safety or compliance documentation for Minus Pad extreme 2?

Available instructions, technical data sheets, safety data sheets and conformity documents for Minus Pad extreme 2 can be found in the downloads section of the product page. Check the exact product name and item number. A technical data sheet does not replace a safety data sheet. If a document or language version is missing, tell us the item number and which document you need.

Downloads "Minus Pad extreme 2"

Color:	gray
Size:	120 x 20 mm
Thickness:	0.5 mm

Goes perfectly with it:

TG Cleaning Wipes

Wet and dry cleaning wipes for cleaning surfaces

$12.75

TG Remove

Effective acetone-based nano-cleaner for removing thermal paste and liquid metal

$13.92

TG Shield

High-temperature protective coating, protects against liquid metal, thermal paste, and short circuits

$13.92